To use any of the sophisticated Compass 6000 Condition Monitoring Software suite functionality a dedicated license is required. There is no meaningful operation supported without that license. Because of this only important software patches – for the most recent versions of all components of the Compass 6000 software suite – are available for download here.

If you are interested in a Compass 6000 demonstration license or you require patch information regarding previous versions of the software, please contact your regional responsible sales representative or our Technical Support Team.

Users who have installed the previous Patch 51627 are recommended to install the current Patch 52238. Patch 52238 fixes, among other things, two bugs caused by Patch 51627 itself, and then shows up in particular, when the user makes changes to the configuration (setup) of the Compass 6000 Condition Monitoring System.

Patch Version 52238 (12/16/2019)
Applicable to main MWS 7126 version: 3.6.49004 (REL19)
Language:  English & Russian
File format: .ZIP [15.3MB]

NOTE: Please close all active Compass 6000 MWS Type 7126 software session prior you install the patch. Consider storing all changes respectively finish your setup activities prior you close the application. The patch has been designed to be applied to the Compass 6000 MWS type 7126, MWS type 7123 and CMM type 3160.

Download the Software

Compass 6000 Monitoring Workstation Type 7123 Software Patch

Patch Version 52238 (12/16/2019)
Applicable to main MWS 7123 version: 3.6.49004 (REL19)
Language:  English & Russian
File format: .ZIP [15.3MB]

NOTE: Please close all active Compass 6000 MWS Type 7123 software session prior you install the patch. Consider storing all changes respectively finish your setup activities prior you close the application. The patch has been designed to be applied to the Compass 6000 MWS type 7126, MWS type 7123 and CMM type 3160.

Download the Software

Compass 6000 Condition Monitoring Module Type 3160 Software Patch

Patch Version52238 (12/16/2019)
Applicable to main CMM 3160 version 3.6.49004 (REL19)
Language:  English & Russian
File format: .ZIP [15.3MB]

NOTE: Please stop the CMM service via the CMM Control Panel software application prior you install the Patch. After a successful patch installation restart again the CMM service via the CMM Control Panel software. During the time the CMM service is stopped, no Condition Monitoring data is collected. The Machine Protection System (VC-6000) is not affected by this and continues to operate without interruption. The patch has been designed to be applied to the Compass 6000 MWS type 7126, MWS type 7123 and CMM type 3160.

Download the Software

Compass 6000 Central Vibration Monitor Version 10 Software Patch

Patch Version 49215 (05/24/2019)
Applicable to main CVMv10 version: 10.1.49004 (REL19)
Language:  English & Russian
File format: .ZIP [0.5MB]

NOTE: Please stop the CVM server via the Compass Commander v10 software application prior you install the patch. After a successful patch installation restart the CVM server via the same Compass Commander v10 application. During the time the CVM server is stopped, no Condition Monitoring data is stored however the Compass 6000 CMM type 3160 server application can buffer data while the patch installation is running and until the CVM server has been restarted. The patch installation takes typically less than a minute.

Download the Software

Compass IMEX-6000 Software Patch

Patch Version 53198 (05/25/2020)
Applicable to main Compass IMEX-6000 main version: 3.0.44811
Language:  English
File format: .ZIP [1,3MB]

Download the Software

Report & Examiner Software PREMIUM

Version download: 2.2.213 
Language: English
File type: .ZIP [77 MB]

We offer “ReX-PREMIUM” free of charge, without copy protection and it comes along with full unlimited functionality and use of time. The main reason for that offer is to offer ReX for two main functionalities which are not implemented in ReO v3:

• Digital Signal Postprocessing DSP of raw vibration data in .wav format. Recorded either with VT-80/VP-80 Modules “Time Signal” or “Tracking”
• For VT-80/VP-80 Module Acceptance test you will necessarily need ReX to draw on and configure predefined or personally defined measurement tasks (setups) which can be stored as Templates.

Download the software

VC-8000/SETPOINT® CMS

VC-8000 Setup & Maintenance Software is used for configuring the system and for performing routine maintenance such as firmware upgrades.  It is also able to emulate the front panel display. Even without a rack connected, the software is useful to those considering the purchase of a VC-8000 system that want to become better familiarized with its capabilities. The can experiment with the software to populate a rack with modules, configure channels and relay logic, and explore the system’s rich signal processing and data acquisition capabilites.

SETPOINT® CMS Software is used when visualizing the condition monitoring data produced by our MPS hardware, whether stored in your OSIsoft PI System or inside our innovative flight recorder – a fully integrated, solid-state hard drive and/or removable SD Card embedded right in the MPS hardware. What’s more, the viewer software is a free download – allowing anyone to open, view, and even save/export data from the SETPOINT® system.

VC-8000

Version date: 7.0.791 [3/20/2020]
MPS Release note (EN)  [3/20/2020]
Language: English
File type: .ZIP [31MB]

• Requires Microsoft .NET Framework 4.5.2 or later.  The web install version of .NET is included in our VC-8000 Setup & Maintenance Software installer package.  The installer will first check to see if .NET is already installed on the computer, and if not, download it from the Microsoft website and install it before the Setup & Maintenance Software installation process proceeds. The computer must be connected to the internet during the installation process unless .NET is already present on it. If this is not possible, download the offline install version of .NET from the Microsoft website. This will allow .NET to be installed on computers without an internet connection. Then, install VC-8000 Setup & Maintenance Software on the computer(s). The install package will automatically detect that .NET is already installed, and the rest of the Setup & Maintenance installation will continue normally.

• This download installs three separate applications known collectively as VC-8000 Setup & Maintenance Software.  It consists of the following:

1. VC-8000 Rack Setup – used to configure a VC-8000 rack
2. VC-8000 Rack Maintenance – used to upgrade firmware, perform rack diagnostics, and other rack maintenance tasks
3. Simulator Launcher – used to emulate the touchscreen display when a physical rack is not connected; primarily intended for demonstration and training purposes

• Refer to the MPS Instruction for additional details on installing and using VC-8000 Setup & Maintenance Software. You can also contact our Technical Support Team for assistance.

NOTE: The differences between the web install and offline install versions are detailed on the Microsoft page accessed via the link above.

Download the Software

Version date: 7.0.792 [3/20/2020]
Language: Russian
MPS Release notes (EN)  [3/20/2020]
File type: .ZIP [32MB]

• This is a Russian-language version of our current production-released English-language MPS software.

Download the Software

VC-8000 Firmware

Firmware is used in the VC-8000 rack’s UMM, TMM, and SAM modules. It is also used with the touchscreen display. However, there is no need to download firmware separately from our configuration software – the two are bundled together. Simply download our VC-8000 Setup & Maintenance Software*. When you connect to a VC-8000 rack, the software will automatically detect the current revision of firmware in all modules and display any applicable newer revisions, allowing you to selectively upgrade.

Contact us for details about Firmware

SETPOINT® CMS

Version date: 7.3.423 [6/22/2020]
Language: English
CMS Release Notes (EN) [6/22/2020]
File type: .ZIP [32MB]

• This download is for SETPOINT® CMS software. CMS can be used to connect to a PI Server where VC-8000 vibration data is stored. It can also be used to open and view an archive file (.CMS file extension). To open an archive file, no additional software is required. To connect to a PI Server, additional OSIsoft PI System components must be installed (see below).
• Connection to a PI Server hosting CMS data requires that the computer running CMS Display also has OSIsoft’s PI AF Client (version 2014 or later) installed.  The installation process for CMS will automatically detect the presence of PI AF Client.  If present, the user will be able to connect to a PI Server.  If not present, the user will only be able to open and view CMS data archives (.CMS file format). PI AF Client is not available for download from this website.  You must obtain it directly from OSIsoft. Alternatively, you may contact  Technical Support  to obtain the installation file and corresponding instructions.
• Data accessible by CMS software is stored in the OSIsoft PI System. PI Server, PI AF Server, and additional OSIsoft components used in the PI System are supplied separately and not downloadable via this website.  For assistance, contact our Technical Support Team.
• Refer to the SETPOINT® CMS Instruction for additional information on installing and using the software.

Download the Software

Sample Machine Data

Version date: 7.3.424 [6/22/2020]
Language: Russian
CMS Release Notes (EN) [6/22/2020]
File type: .ZIP [32MB]

• This is a Russian-language version of our current production-released English-language CMS software.

Download the Software

SETPOINT®-to-PI Adapter

Version date: 7.3.423 [6/22/2020]
Language:English
CMS Release Notes (EN) [6/22/2020]
File type:.ZIP [8MB]

• This application enables communications between one or more VC-8000 racks and a PI Server. The computer running this adapter is normally a PI Server but the software may alternatively reside on a separate computer in the PI Server’s network.
• The computer running SETPOINT®-to-PI Adapter must also have OSIsoft’s PI AF Client (version 2014 or later) installed.  The installation process will automatically detect the presence of PI AF Client and prompt the user accordingly.  PI AF Client is not available for download from this website.  You must obtain it directly from OSIsoft.  Alternatively, you may contact Technical Support to obtain the installation file and corresponding instructions.
• PI Server, PI AF Server, Microsoft SQL, and additional OSIsoft components used in the PI System are supplied separately and not downloadable via this website.  For assistance, contact our Technical Support Team.
• Refer to SETPOINT® CMS Instruction for additional details.  You may also contact our Technical Support Team.

Download the Software

Version date: 7.3.424 [6/22/2020]
Language:Russian
CMS Release Notes (EN) [6/22/2020]
File type: .ZIP [8MB]

• This is a Russian-language version of our current production-released English-language SETPOINT®-to-PI Adapter software.

Download the Software

We’re reachable 16 hours each day via phone using the numbers below, or you can email us.

Technical Support

Hotline for support: 

 +49 6151 428 1400

Technical support

Darmstadt, Germany
Main switchboard: +49 (0) 6151 428 0
E-Mail: support@bkvibro.com

Nærum, Denmark
Main switchboard: +45 77 41 25 00

Gardnerville, Nevada
Main switchboard: +1 (775) 552 3110
E-Mail: support@bkvibro.com